| User | Post |
|
3:18 pm
September 17, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
I HAVE A 98 DODGE WITH 2 O2 SENSORS ONE IN FRONT OF CONVERTER AND ONE AFTER THE CONVERTER DO I NEED 2 ENHANCERS AND WHEN YOU ADJUST THE MIXTURE SHOULD THE VOLTAGE INCRESS OR DECRESS
|
|
|
3:56 pm
September 17, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
The enhancer is not for the O2 sensor is for the MAP or the MAF sensors.
When using the enhancer the voltage at the signal wire on the MAP/MAF sensor is going to decrease when adjusting the mixture to lean.
Oxygen sensors, you only need to work on the upstream sensors (before the catalitic converters). Try extensions first before spending on an EFIE.
EFIE is to add voltage to the signal of the O2 sensor.
Are you having problem with your mpg? Let me know I will try to help you.
Robert
|
|
|
1:35 pm
September 18, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
a exstender is not a option do not have room . you say use th up stream sensor it has 4 wires 2 are white they are heater wires 12 volts 1black wire it has + voltage and a gray wire it hase – voltage which wire do i hood the engancer to i have had it hooked up to both and the black wire the voltage has a big change going down as i lean it out but the truck richens up and the gray wire shows verry little change of voltage from -6 to -4
|
|
|
2:03 pm
September 18, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
which wire do i hood the engancer to
NONE, The enhancer is not for the Oxygen sensors. The only two things you can use on the Oxygen sensors are extenstions or an EFIE
The enhancer is for the MAP or MAF sensors. You need to install the enhancer on any of these two sensors. Jeff, please let me know that you understood.
Robert
|
|
|
12:38 am
September 19, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
ok i think i under stand now the water for gas confused me i need to hook up the enhanser to the map sensor give me some direction on this please and will try it this weekend thanks for geting me on the right track
|
|
|
1:49 am
September 19, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
o2 sensors extendrs can i drill a new hole and tap it a little fwd of the original hole and put the estender and o2 sensor in there have also heard that aluminum foil raped around o2 sensor will help ??????????
|
|
|
10:34 am
September 19, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
To help you on your specific car I need you to get the sensor diagram and I can help you. You can buy it here (I get it from a contact for $3.99) Just make sure to put all the vehicle info Year, Make, Model, and the 8 code (From left to right standing if front of the car) of the VIN (The number that you see thru the windshield). Please don't do nothing like that with the O2s is cheaper to get an EFIE and I have not try aluminum foil so I don't know if that is going to work.
Robert
|
|
|
6:36 pm
September 19, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
I FOUND WHERE TO PURCHES THE DAIGRAM BUT DO I NEED TO PAY BEFORE GIVE ALL THE INFO AND DO YOU WANT THE WHOLE VIN NUMBER OR JUST THE LAST 8 DIGETS BECAUS MY VIN NUMBER HAS 17 DUGETS
|
|
|
10:48 pm
September 19, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
Jeff,
Yes, at check out fill the info at the bottom of the page. You can go ahead and give me the 17 digits, it's ok.
Robert
|
|
|
11:16 pm
September 19, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
went and purchced the wire digram did not see where to put vin number
|
|
|
11:37 pm
September 19, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
Don't worry, just post it here.
|
|
|
9:12 am
September 20, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
dodge 1500 4×4 vin #1b7hf13y6wj203437
|
|
|
9:14 pm
September 20, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
The wire that we need to cut is the Dark Green/Red pin # 2.
When you cut that wire you will have two ends. One end is coming from the sensor, here you will connect the wire labeled MAP/MAF on the enhancer. The other end is going to the computer, connect the wire labeled ECM on the enhnacer. The wire labeled ground on the enhancer goes to chassis ground.
Let me know if this helps you.
Robert
|
|
|
3:57 pm
September 21, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
robert hooded up enhanser as told now tell me if my truck should do this when put in enhance and knod to lean the rpm goes up 400 rpm if i turn the knob quick the engine stumbles and catches back up there in no change in egt just a thought should the engine stumble and stay that way till i give it more fuel with the knob and it may sound crazy but if i put 2 engancers in series what will that do
|
|
|
3:59 pm
September 21, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
forgot to tell you this is with hho gen off. me and some friends were wonderng how much hho do you need to make . now we are making a gallin ever 2 min is this enough or ts much
|
|
|
8:57 pm
September 21, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
Jeff,
When you install the generator and turn the knob all the way to lean the engine will stall. The enhancer should only be used if your generator is on producing hho otherwise the engine is gonna be running too lean and you can damage it. To adjust the enhancer wait until the engine is at operating temperature with the hho generator on and start turning the knob toward the 0 setting until you find the setting that you feel the engine still runs good.
Are making a gallon or a liter every two minutes?
|
|
|
10:18 am
September 22, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
|
10:26 am
September 22, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
what is efie and how does it word and how much does it coast
|
|
|
3:56 pm
September 22, 2008
|
admin
Admin
| | | |
|
| posts 114 |
|
|
That's 2 liters a minute that is a very good production. Do know the amperage that it draws at 12vdc?
The EFIE adds voltage to the O2 signal and the costs varies. I been trying to put an EFIE and a PWM for a while now but there is not enough hours in a day for all the projects I got going. If you have not bought one by the time I complete it, I'll let you know.
|
|
|
12:43 am
September 23, 2008
|
jeff6
Member
| | | |
|
| posts 14 |
|
|
with 2 tea spoons of backing powedr per gal it draws 50 amps am having some problems with heat am going to get some help from my cousin wo is a elec eng at nasa if he can find the time sounds like you my gen is 11 plates 3.5 x 7.5 1/4 inch apart looks like the water is boiling when its on am trying a new stile same plate size but it lined up -nn+nn+nn- not sure how much out put yet i haave a leak getting some sealent that we use at work for acft fuel cells
|
|
Login
Register
Search 
Forums
Topic RSS 
